There is a conceptual link between board support packages and a HAL (Hardware Abstraction Layer) in the sense that the device drivers / kernel modules perform the hardware abstraction and the board support package provides an interface to the device drivers or is the hardware abstraction layer itself.
So basically a BSP has a functionality similar to the BIOS in the DOS era:
Additionally the BSP is supposed to perform the following operations
- Initialize the processor
- Initialize the bus
- Initialize the interrupt controller
- Initialize the clock
- Initialize the RAM settings
- Configure the segments
- Load and run bootloader from flash
From: Board support package (Wikipedia)
The BIOS in modern PCs initializes and tests the system hardware
components, and loads a boot loader from a mass memory device which
then initializes an operating system. In the era of DOS, the BIOS
provided a hardware abstraction layer for the keyboard, display, and
other input/output (I/O) devices [device drivers] that standardized an interface to
application programs and the operating system. More recent operating
systems do not use the BIOS after loading, instead accessing the
hardware components directly.
Source: BIOS (Wikipedia)
Another aspect is the usage of device trees in BSPs, the device tree is a unifying or standardizing concept to describe the hardware of a machine:
U-boot boot loader and getting ready to ship
Doug Abbott, in Linux for Embedded and Real-Time Applications (Fourth
Edition), 2018
Device Trees
One of the biggest problems with porting an operating system such as
Linux to a new platform is describing the hardware. That is because
the hardware description is scattered over perhaps several dozen or so
device drivers, the kernel, and the boot loader, just to name a few.
The ultimate result is that these various pieces of software become
unique to each platform, the number of configuration options grows,
and every board requires a unique kernel image.
There have been a number of approaches to addressing this problem. The
notion of a “board support package” or BSP attempts to gather all of
the hardware-dependent code in a few files in one place. It could be
argued that the entire arch/ subtree of the Linux kernel source tree
is a gigantic board support package.
Take a look at the arch/arm/ subtree of the kernel. In there you will
find a large number of directories of the form mach-* and plat-*,
presumably short for “machine” and “platform,” respectively. Most of
the files in these directories provide configuration information for a
specific implementation of the ARM architecture. And of course, each
implementation describes its configuration differently.
Would not it be nice to have a single language that could be used to
unambiguously describe the hardware of a computer system? That is the
premise, and promise, of device trees.
The peripheral devices in a system can be characterized along a number
of dimensions. There are, for example, character vs block devices.
There are memory mapped devices, and those that connect through an
external bus such as I2C or USB. Then there are platform devices and
discoverable devices.
Discoverable devices are those that live on external busses, such as
PCI and USB, that can tell the system what they are and how they are
configured. That is, they can be “discovered” by the kernel. Having
identified a device, it is a fairly simple matter to load the
corresponding driver, which then interrogates the device to determine
its precise configuration.
Platform devices, on the other hand, lack any mechanism to identify
themselves. System on Chip (SoC) implementations, such as the Sitara,
are rife with these platform devices—system clocks, interrupt
controllers, GPIO, serial ports, to name a few. The device tree
mechanism is particularly useful for managing platform devices.
The device tree concept evolved in the PowerPC branch of the kernel,
and that is where it seems to be used the most. In fact, it is now a
requirement that all PowerPC platforms pass a device tree to the
kernel at boot time. The text representation of a device tree is a
file with the extension .dts. These .dts files are typically found in
the kernel source tree at arch/$ARCH/boot/dts.
A device tree is a hierarchical data structure that describes the
collection of devices and interconnecting busses of a computer system.
It is organized as nodes that begin at a root represented by “/,” just
like the root file system. Every node has a name and consists of
“properties” that are name-value pairs. It may also contain “child”
nodes.
Listing 15.1 is a sample device tree taken from the devicetree.org
website. It does nothing beyond illustrating the structure. Here we
have two nodes named node1 and node2. node1 has two child nodes, and
node2 has one child. Properties are represented by name=value. Values
can be strings, lists of strings, one or more numeric values enclosed
by square brackets, or one or more “cells” enclosed in angle brackets.
The value can also be empty if the property conveys a Boolean value by
its presence or absence.
Source: Board Support Package (ScienceDirect)
Via device tree overlays kernel modules can be loaded at boot time, i.e., on Raspberry Pi adding dtoverlay=lirc-rpi to /boot/config.txt loads the lirc-pi kernel module/device driver:
A future default config.txt may contain a section like this:
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
If you have an overlay that defines some parameters, they can be
specified either on subsequent lines like this:
dtoverlay=lirc-rpi
dtparam=gpio_out_pin=16
dtparam=gpio_in_pin=17
dtparam=gpio_in_pull=down
Source: Configuration (Raspberry Pi Documentation)
When building BSPs with Yocto, all the hardware information that is scattered over device drivers, the kernel, the boot loader, etc. is gathered. Here is the developer's guide how this can be done in Yocto: Yocto Project Board Support Package Developer's Guide
[Yocto documentation]... states that the BSP “…is concerned with the
hardware-specific components only. At the end-distribution point, you
can ship the BSP combined with a build system and other tools.
However, it is important to maintain the distinction that these are
separate components that happen to be combined in certain end
products.”
Source: Board Support Package: what is it?
