How to install feature based on the property set in custom action?

Question

I am trying to install one from two features based on the value that should be set inside of the custom action.
Firstly, I set the value of a property:

UINT __stdcall ConfigurationCheckAction(MSIHANDLE hInstall)
{
    HRESULT hr = S_OK;
    UINT er = ERROR_INSTALL_FAILURE;

    hr = WcaInitialize(hInstall, "ConfigurationCheckAction"); 
    if (condition) {
         MsiSetProperty( hInstall, TEXT("STREAM"), TEXT("RED") );
    }
    else {
         MsiSetProperty( hInstall, TEXT("STREAM"), TEXT("BLUE") );
    } 
    return WcaFinalize(er);
}

Secondly, I make two conditions per two features:

<Feature Id='Complete' Level='1'>
     <Feature Id="Red" ConfigurableDirectory="TARGETDIR" Title="F1" Level="0">
     <Condition Level="1">STREAM</Condition>
     </Feature>
     <Feature Id="Blue" ConfigurableDirectory="TARGETDIR" Title="F2" Level="0">
     <Condition Level="1">NOT STREAM</Condition>
     </Feature>
</Feature>

Note that I don't define property inside of the wxs file previously, as I would like to set it from the custom action.

My custom action is called before InstallInitialize and Execute is immediate.

From the installation log I have confirmation that the property is set. However, my conditional installation does not work, as it seems like what is in the condition is always evaluated as false.

I tried evaluating conditions: STREAM, STREAM=RED, STREAM="RED", < ![CDATA[STREAM=RED]]>

I am running out of ideas what to do and would appreciate help.

Prefect

Define the property you want to use (it doesn't need a value) in the wxs and make sure you set Secure='yes'. You may have to update your conditions but this should allow the porperty's new value to pass through to your elevated section of the install. – Demijohn

Answer 1

Thank you for your replies. In the end, a combination of your suggestions helped me.

I want to state what did and what did not work:

1. Adding property to WiX with a default value was not necessary (as well with adding property of this property Secure='yes')
2. Calling custom action before CostInitialize did not solve the problem on its own, but I believe it was one of the factors that resolved an issue.
3. Conditional sintax was corrected by:
   a) Putting condition inside of CDATA and adding quotes to the value of property as suggested: <Condition><![CDATA[STREAM="RED"]]></Condition>
   b) Reversing condition levels so feature has condition level 1 and condition has level 0. This means that feature is always installed, unless the condition expression is false.

Prefect

Answer 2

Too late to test all of this, but here goes with some information. I will check back tomorrow. Essentially I think the problem is your custom action sequencing. Try before Costing.

Some things to consider:

• Custom action sequencing: you need to sequence your custom action right and it needs to be present in both silent and interactive installation modes.
  • Did you try to sequence the set property custom action before CostInitialize? You state you set it before InstallInitialize, but try it before CostInitialize instead (you might have tried).
  • And did you remember to insert this custom action in the InstallUISequence as well as the InstallExecuteSequence? You need to insert in both sequences in case the setup runs in silent mode. Before CostInitialize in both sequences I believe.
• Feature Level: manipulating features via the feature level and INSTALLLEVEL is just one way to do feature control, you can also set features via the command line or using a custom action.
  • Setting a feature level to 0 should hide the feature from view in the setup's custom dialog.
  • Setting a feature level higher than the setup's INSTALLLEVEL will deselect the feature from installation.
  • And the other way around setting a feature level lower or equal to the setup's INSTALLLEVEL will select the feature for installation.
  • The conditional syntax allowed is quite flexible, and could provide the functionality you need outright - but I have never used them properly. Here is an example from the Installshield forum.
• ADDLOCAL & REMOVE: you can manipulate the feature selection by changing the values of the ADDLOCAL and REMOVE properties from a custom action (technically also REINSTALL and ADVERTISE) - and these properties can be set via the command line as well.
• Win32: you can also use the Win32 functions MsiGetFeatureState and MsiSetFeatureState - from a C++ custom action - to set feature selection.

Frankly it is a bit mad the whole thing. Also keep in mind that there are feature action states (what is going to happen to a feature) and feature installed states (what state it is in). The Win32 function documentation should explain.

---

Cross-linking for easy retrieval:

• Unselected Feature Being Installed

Anis

Answer 3

I have done something similar, but we ended up controlling this at a component level(adding the condition to the <Component/> elements instead of the feature element using a transform during heat). But our condition utilizes CDATA while also using double quotes for the value, which you don't list in what you've tried. So first I'd try the following conditions in your features:

<Condition><![CDATA[STREAM="RED"]]></Condition>
<Condition><![CDATA[STREAM="BLUE"]]></Condition>

If that still does not work, I would try the following:

1. Add the STREAM property with a default value to your WiX. Then test it with that default value to see if having the default value set to begin with makes it work. That could mean you need to set the property sooner, possibly off a UI event. <Property Id="STREAM" Value="RED"/>

2. As a last resort, you could add the conditions to each component as I did, but we only did that for very specific reasons, hopefully you can get the conditional feature to work with the above suggestions!

I hope the above fixes your problem, or at least leads you to the answer!

Forgave

Answer 4

Concerning the correct order of the custom actions, the description of the custom action type 51 contains the decisive hint:

"To affect a property used in a condition on a component or feature, the custom action must come before the CostFinalize action in the action sequence."

Dissert